zdravim najskor poviem ze som uplny zaciatocnik..:) nainstaloval som debian na PC a po prikaze reboot alebo shutdown mi PC len ukonci vsety servisy ale nerestartne sa a ani sa nevypne.
HELP PLS.... dakujem
debian reboot
Pre pridávanie komentárov sa musíte prihlásiť.
a urobil som vypis acpi no mne to vela nepovedalo ...
BIOS-e820: 000000002dff0000 - 000000002dff3000 (ACPI NVS)
BIOS-e820: 000000002dff3000 - 000000002e000000 (ACPI data)
ACPI: RSDP (v000 AWARD ) @ 0x000f7e50
ACPI: RSDT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2dff3040
ACPI: FADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2dff30c0
ACPI: MADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2dff6cc0
ACPI: DSDT (v001 AWARD AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: Core revision 20060707
ACPI: bus type pci registered
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
ACPI: (supports S0 S1 S4 S5)
ACPI: Fan [FAN] (on)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x1
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x2
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x3
ACPI: Thermal Zone [THRM] (44 C)
ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 177
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 193
ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 201
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 209
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 217
ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 225
posledne co je napisane
synchronizing SCSI cache for disk sda:
restarting system.
.
pri reboote na restarting system
pri shutdown alebo poweroff system halt
no este verzia kernelu 2.6.18-6-686 #1 SMP Fri Jun 6 22:22:11 UTC 2008 i686 GNU/Linux
skoncilo to tak isto...
restarting system
ale pocitac sa nerestartol.... som zufaly...:(
Tomuto nasvedcuje aj posledna hlaska (synchronizing disks, remooting alebo power off).
Inak dalo sa to aj obist parametrom NOACPI alebo NOAPIC ale to len zakaze podporu danej technologie. Po aktivovani daneho parametru vsak moze blbnut rezim riadenia spotreby a chladenia komponentov(nevravim ze musi, ale moze). Poslednym vychodiskom je predlzovacka s vypinacom, toto riesenie je v dnesnej dobe ajtak najlepsie pretoze pocitace maju odber naprazdno aj ked su zevraj vypnute. Doma to tak mam a nestazujem sa.
no zdrojom to urcite nebude... bol tam predtym nainstalovany WIN a restartoval sa a vypinal jedna basen... dokonca aj s vypnutym ACPI.
skusim teda este pozriet novy bios kazda rada je dobra...:)
Takze sa nemas coho bat. Ak robis cez ssh, tak pouzi screen. Ten si pripojis a odpojis bez problemov. A ak pouzivas napriklad VNC (idealne tunelovane cez ssh, hoci aj cez putty), tak pouzi x11vnc. V oboch spomenutych pripadoch mozes potom pokracovat aj doma a stlacit to tlacitko reboot.
PS.: ale s tym biosom a novsim jadrom, s tym sa to obvykle pohlo dalej.
aj ked hovoris ze sa bat nemusim bol by som rad keby som sa nemusel bat restartovat PC...:)
vkazdom pripade skusim ten bios a jadro...
aj este niekoho nieco napadne dajte napiste...
PS:ja dam vediet ako som dopadol po upgrade: bios a jadra
ma to najnovsi dostuony bios
jadro 2.6.25
no moj problem stale trva ..... PC sa jednoducho nerestartne ani nevypne...
aj ked posledna hlaska je teraz ina...:)))
464.683016 system reboot
464.683016 machine restart
Pri poziadavke na reboot mozes potvrdit prikaz aj z domu (pripojenim screenu na iny terminal alebo sadnutim za graficke sedenie) a stlacit to tlacitko co mas na dosah ruky. Toto je dan za to ze specifikacia ACPI ma cez 600 stran. Prepytujem len specifikacia, nie prirucka.
PS.: co dodat :)