Madwifi a wifi karta CM9 problem

Sekcia: Konfigurácia 10.01.2012 | 19:14
Buri   Návštevník
Cawte. Potrebujem poradit v jednej veci.
Kupil som si tuto kartu http://wifi.aspa.cz/cm9-minipci-bezdratova-karta-ar5213-5004x-z46249/ (teda mam 5001x) s touto redukciou do mojho mini home servera, kde chcem spravit WiFi AP.

(mam tam linux squeeze 6.0.3, inak povedané kernel 2.6.32-5-amd64)
Driver som stiahol z madwifi-project.org (ten HAL (this snapshot) a nie rovny release kvoli tomu ze mi to neslo skompilovat a docital som sa ze to tak ma byt).
Tak som to stiahol, rozbalil, nainstaloval, (make),
hodil som do /etc/modules: ath_pci a do
/etc/modprobe.d/madwifi som hodil riadok: options ath_pci autocreate=none rfkill=0 outdoor=1.

hodil som pre istotu cely restart, pozeram asi to ide. Pozriem iwconfig a tam toto:
root@junior:~# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

eth1      no wireless extensions.

wlan0     IEEE 802.11abg  ESSID:off/any
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
# pokial viem, ma sa vytvorit zariadenie wifiX (wifi0) ale to je asi jedno. či?

takže zjavne funkčné.
po lsmod | grep ath:
root@junior:~# lsmod | grep ath
ath_pci                73669  0
wlan                  161166  1 ath_pci
ath_hal               214125  1 ath_pci
ath5k                 112210  0
mac80211              137372  1 ath5k
ath                     8006  1 ath5k
cfg80211              101496  3 ath5k,mac80211,ath
led_class               2433  1 ath5k

aj to vypadá fajn. ALE.
Pokial viem , musim vytvoriť logicke rozhranie (napr. athX) na toto fyzicke zariadenie.
Nejak takto:
root@junior:~# wlanconfig ath1 create wlandev wlan0
wlanconfig: ioctl: Operation not supported

A toto je ten problem. Prečo nechce wlanconfig vytvorit toto logicke zariadenie ath1 ? Teda preco operacia nie je podporovana kedze VIEM! ze tato wifi karta CM9 PODPORUJE taketo veci. (napr.: tu je ukazka zo stranky Petra Simandla (http://www.simandl.cz/stranky/linux/atheros/atheros.htm)).

Dopedu vďaka za pomoc.


-- ešte len na doplnenie:

dmesg | grep ath:
root@junior:~# dmesg | grep ath
[    4.669159] atheros_eth 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.669175] atheros_eth 0000:01:00.0: setting latency timer to 64
[    5.681788] ath5k 0000:02:0e.0: PCI INT A: no GSI - using IRQ 11
[    5.681933] ath5k 0000:02:0e.0: registered as 'phy0'
[    6.139451] ath: EEPROM regdomain: 0x0
[    6.139457] ath: EEPROM indicates default country code should be used
[    6.139461] ath: doing EEPROM country->regdmn map search
[    6.139467] ath: country maps to regdmn code: 0x3a
[    6.139471] ath: Country alpha2 being used: US
[    6.139474] ath: Regpair used: 0x3a
[    6.219404] ath5k phy0: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
[    6.219411] ath5k phy0: RF5112B multiband radio found (0x36)
[    6.240153] ath_hal: module license 'Proprietary' taints kernel.
[    6.243939] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[    6.384262] ath_pci: svn r4176 (branch madwifi-0.9.4)

a lspci | grep Wireless
root@junior:~# lspci | grep Wireless
02:0e.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01)
    • Re: Madwifi a wifi karta CM9 problem 10.01.2012 | 19:44
      Buri   Návštevník
      Alebo nemôže byť chyba tu?

      lspci -v:
      02:0e.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01)
              Subsystem: Wistron NeWeb Corp. CM9 Wireless a/b/g MiniPCI Adapter
              Flags: bus master, medium devsel, latency 168, IRQ 11
              Memory at febe0000 (32-bit, non-prefetchable) [size=64K]
              Capabilities: [44] Power Management version 2
              Kernel driver in use: [b]ath5k[/b]
      

      Ak hej tak prosim vas čo s tým? :)