Touchpad & USB mys

Sekcia: Aplikácie & Desktop 02.11.2005 | 13:53
Avatar Vendo Slackware  Používateľ
Ahojte naozaj som zufaly. Zacal som s Linuxom len pred chvilkou a neviem ako rozchodit usb mysku. Chodi mi len touchpad. Mam Slackware 10.2. Dik za odpoved
    • Re: Touchpad 30.10.2005 | 17:39
      ps   Návštevník
      otvor subor /etc/X11/xorg.conf a v Section "InputDevice" (samozrejme pre mys) to takto zmen: Option "Protocol" "usb" alebo skusOption "Protocol" "Auto". A ak ti nepojde koliecko na nej tak na koniec tej sekcie dopis Option "ZAxisMapping" "4 5"
      • Re: Re: Touchpad 30.10.2005 | 17:43
        Vendo   Návštevník
        to nastavenie bolo "auto" a nepomohlo ani "usb" stale bezi iba touchpad a usb uplne nic:) ked sol nastavene usb tak nesiel ani touchpad
        • Re: Re: Re: Touchpad 30.10.2005 | 18:10
          ps   Návštevník
          zrejme bude problem niekde inde ,tipujem ze v pripojeni mysi .V Option "Device" "/dev/........\" ,mas co nastavene?
    • Re: Touchpad 30.10.2005 | 20:05
      kajn   Návštevník
      inak to sprav. stiahni si z netu driver pre synaptics touchpad. (ak ho mas) Potom editujuj /etc/X11/xorg.conf tak ze tam pridas pre ten touchpad synaptics. pre dalsie zariadenie (USB MYS) je protokol IMPS/2. na koniec /etc/X11/xorg.conf si potom pridaj input device touchpad a dalej parameter always core. pre usb mys si nechaj nechaj trebars nazov usb mys (to je to co je v identifier) a parameter corepointer. malo by to fungovat. kazdopadne si ale zmen /etc/inittab na runlevel 3. aby ti to bootovalo do textoveho rezimu. vyskusaj a ak by sa vyskytla chyba tak ti ju vypise.
      • Re: Re: Touchpad 30.10.2005 | 22:48
        Vendo   Návštevník
        Problem je v tom ze mi nefunguje USBcko a TouchPad ide v pohode a neviem si rady som uplny amater a nechodi a nechodi uz som stravil na nete hodiny ohladom tohto.....
        • Re: Re: Re: Touchpad 30.10.2005 | 23:14
          peter golis   Návštevník
          tak sem daj vypis prikazov /sbin/lspci -v /sbin/lsmod
    • Re: Touchpad 31.10.2005 | 01:19
      Descartes   Návštevník
      Pokus sa nainstalovat coldplug a hotplug, tym sa ti nacitaju automaticky mody pri pripojeni nejakeho USB zariadenia a malo by ti to ist.. ja som nemusel v konfiguracii nic menit a islo to hned (v gentoo a v Kubuntu)... snad by malo aj na mandrive..
    • Re: Touchpad 31.10.2005 | 01:56
      jariq   Návštevník
      No v prvom rade treba spravne nastavit vstupne zariadenia v v konfiguraku x-serveru /etc/X11/xorg.conf (uvadzam len dolezite casti): ... Section "InputDevice" Identifier "Touchpad" Driver "mouse" Option "Device" "/dev/mouse" Option "Protocol" "PS/2" EndSection Section "InputDevice" Identifier "USBMouse" Driver "mouse" Option "Device" "/dev/input/mice" Option "Protocol" "ExplorerPS/2" Option "Buttons" "7" Option "ZAxisMapping" "4 5" EndSection ... Section "ServerLayout" ... InputDevice "Touchpad" "CorePointer" InputDevice "USBMouse" "AlwaysCore" ... EndSection No a dalsia moznost, preco ti to nemusi chodit je tupost hotplug scriptov. Riesil som to uz na linuxquestions.org
      • Re: Re: Touchpad 31.10.2005 | 08:17
        Vendo   Návštevník
        lspci -v 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 650/M650 Host (rev 80) Flags: bus master, medium devsel, latency 64 Memory at e0000000 (32-bit, non-prefetchable) [size=64M] Capabilities: [c0] AGP version 2.0 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 99 Bus: primary=00, secondary=01, subordinate=01, sec-latency=68 Memory behind bridge: e5000000-e5ffffff Prefetchable memory behind bridge: e8000000-efffffff 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge) (rev 14) Flags: bus master, medium devsel, latency 0 00:02.3 FireWire (IEEE 1394): Silicon Integrated Systems [SiS] FireWire Controller (prog-if 10 [OHCI]) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, medium devsel, latency 64, IRQ 3 Memory at e4000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at [disabled] [size=128K] Capabilities: [64] Power Management version 2 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (prog-if 80 [Master]) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, medium devsel, latency 128 I/O ports at 1000 [size=16] 00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev a0) (prog-if 00 [Generic]) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: medium devsel, IRQ 5 I/O ports at 1400 [size=256] I/O ports at 1080 [size=128] Capabilities: [48] Power Management version 2 00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] Sound Controller (rev a0) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, medium devsel, latency 173, IRQ 5 I/O ports at 1c00 [size=256] I/O ports at 1800 [size=128] Capabilities: [48] Power Management version 2 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, medium devsel, latency 64, IRQ 10 Memory at e4001000 (32-bit, non-prefetchable) [size=4K] 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, medium devsel, latency 64, IRQ 10 Memory at e4002000 (32-bit, non-prefetchable) [size=4K] 00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, medium devsel, latency 64, IRQ 10 Memory at e4003000 (32-bit, non-prefetchable) [size=4K] 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller (prog-if 20 [EHCI]) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, medium devsel, latency 64, IRQ 10 Memory at e4004000 (32-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 2 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 91) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, medium devsel, latency 173, IRQ 10 I/O ports at 2000 [size=256] Memory at e4005000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at [disabled] [size=128K] Capabilities: [40] Power Management version 2 00:0a.0 CardBus bridge: O2 Micro, Inc. OZ601/6912/711E0 CardBus/SmartCardBus Controller Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, stepping, slow devsel, latency 168, IRQ 3 Memory at 20000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=03, subordinate=03, sec-latency=176 Memory window 0: 20400000-207ff000 (prefetchable) Memory window 1: 20800000-20bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff 16-bit legacy interface ports at 0001 01:00.0 VGA compatible controller: nVidia Corporation NV31M [GeForce FX Go5600] (rev a1) (prog-if 00 [VGA]) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, 66Mhz, medium devsel, latency 248, IRQ 10 Memory at e5000000 (32-bit, non-prefetchable) [size=16M] Memory at e8000000 (32-bit, prefetchable) [size=128M] Expansion ROM at [disabled] [size=128K] Capabilities: [60] Power Management version 2 Capabilities: [44] AGP version 3.0
        • Re: Re: Re: Touchpad 31.10.2005 | 08:19
          Vendo   Návštevník
          lsmod Module Size Used by Tainted: P ohci1394 23888 0 (unused) ieee1394 41636 0 [ohci1394] snd-intel8x0 18304 0 snd-ac97-codec 58556 0 [snd-intel8x0] snd-pcm 54344 0 [snd-intel8x0 snd-ac97-codec] snd-timer 13764 0 [snd-pcm] snd 32772 0 [snd-intel8x0 snd-ac97-codec snd-pcm snd-timer] soundcore 3396 0 [snd] snd-page-alloc 4712 0 [snd-intel8x0 snd-pcm snd-timer snd] usb-ohci 19368 0 (unused) ehci-hcd 17516 0 (unused) usbcore 59148 1 [usb-ohci ehci-hcd] sis900 12780 1 crc32 2880 0 [sis900] nvidia 3421740 7 ds 6548 2 yenta_socket 10436 1 pcmcia_core 39172 0 [ds yenta_socket] ntfs 51232 2 (autoclean) ide-scsi 9392 0
          • Re: Re: Re: Re: Touchpad 31.10.2005 | 14:03
            peter golis   Návštevník
            lspci: 00:03.X USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: Acer Incorporated [ALI]: Unknown device 0028 Flags: bus master, medium devsel, latency 64, IRQ 10 Memory at e4001000 (32-bit, non-prefetchable) [size=4K] lsmod: usb-ohci 19368 0 (unused) ---- pozitivna sprava je ze su pouzite spravne ovladace. otazne je ci je vhodnejsie pouzit coldplug/hotplug s tym ze sa nacitaju vsetky potrebne ovladace pri pripojeni alebo ci sa oplati pohladat ovladac pre USB HID (usb keyboard, mouse).
            • Re: Re: Re: Re: Re: Touchpad 31.10.2005 | 15:25
              Vendo   Návštevník
              Je mozne to povedat nejako "ludsky" s linuxom robim cca 48 hodin :)
              • Re: Re: Re: Re: Re: Re: Touchpad 31.10.2005 | 15:34
                peter golis   Návštevník
                podpora pre USB je spravna. mozno treba zaviest modul pre usb mysku pretoze sa nezaviedol aj sam (chybala sluzba hotplug/coldplug), mozno sa zaviedol ale v konfiguraku pre xwindows je definovana mys zle (prispevok od jariqa). ako vyzera zodpovedajuca cast konfiguraku pre x.org?
                • Re: Touchpad 31.10.2005 | 16:55
                  Avatar Vendo Slackware  Používateľ
                  Toto by malo stacit "asi" Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" RgbPath "/usr/X11R6/lib/X11/rgb" ModulePath "/usr/X11R6/lib/modules" FontPath "/usr/X11R6/lib/X11/fonts/misc/" FontPath "/usr/X11R6/lib/X11/fonts/TTF/" FontPath "/usr/X11R6/lib/X11/fonts/Type1/" FontPath "/usr/X11R6/lib/X11/fonts/CID/" FontPath "/usr/X11R6/lib/X11/fonts/75dpi/" FontPath "/usr/X11R6/lib/X11/fonts/100dpi/" EndSection Section "Module" Load "extmod" Load "dri" Load "glx" Load "dbe" Load "record" Load "xtrap" Load "type1" Load "freetype" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "usb" Option "Device" "/dev/mouse" EndSection
                  • Re: Re: Touchpad 01.11.2005 | 07:02
                    peter glis   Návštevník
                    no, a zariadenie /dev/mouse ukazuje kam? ls -l /dev/mouse alebo, nebolo by rozumnejsie tam dat rovno /dev/input/mice ?
                    • Re: Re: Re: Touchpad 02.11.2005 | 13:53
                      Avatar Vendo Slackware  Používateľ
                      Dakujem moc krat druha rada zabrala --> slape:) este raz dakujem