napalovanie pomocou cdrecord

Sekcia: Hardware a Drivery 07.02.2007 | 22:02
Avatar Dušan Ďurech Debian Lenny 5.0  Používateľ
Dobry den,

mam Free Mandriva Linux 2007
jadro : 2.6.20

cdrecord -version
Cdrecord-ProDVD-Clone 2.01.01a11 (i686-pc-linux-gnu) Copyright (C) 1995-2006 J�g Schilling

cdrecord -scanbus -dev=ATA
Cdrecord-ProDVD-Clone 2.01.01a11 (i686-pc-linux-gnu) Copyright (C) 1995-2006 J�g Schilling
scsidev: 'ATA'
devname: 'ATA'
scsibus: -2 target: -2 lun: -2
Warning: Using badly designed ATAPI via /dev/hd* interface.
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.8'.
scsibus1:
1,0,0 100) *
1,1,0 101) 'HL-DT-ST' 'DVD-RAM GSA-H20L' '1.01' Removable CD-ROM

Vcera som napaloval ISO obraz pomocou prikazu:
cdrecord dev=/dev/hdd KNOPPIX_V5.1.1CD-2007-01-04-EN.iso
prebehlo OK

Dneska som chcel napalit, dalsie pomocou :
cdrecord speed=8 dev=/dev/hdd GamesKnoppix-3.7-0.2-EN.iso
ale napise mi to :

Sence Key: 0x4 hardware Error, Segment 0
cmd finished after 8.684s timeout 40s
write track data: error after 1015808 bytes
cdrecord: A write error occured
cdrecord: please properly read the error message above.
cdrecord: Success. close track/session: scsi sendcmd: no error

potom som napalovanie simuloval pomocou "dummy" a ziadne chyby nenastali.

Za odpovede vopred dakujem.
    • Re: napalovanie pomocou cdrecord 07.02.2007 | 22:26
      Avatar uid0 Debian  Používateľ
      pochybujem, ze este niekto okrem teba pouziva "Cdrecord-ProDVD-Clon"

      dvd+rw-tools
      wodim
      Debian. apt-get into it…
      • Re: napalovanie pomocou cdrecord 08.02.2007 | 15:30
        Avatar Dušan Ďurech Debian Lenny 5.0  Používateľ
        Diky

        Stiahol som si zdrojaky :
        http://ftp.debian.org/debian/pool/main/c/cdrkit/cdrkit_1.1.2.orig.tar.gz

        hmm, nemam cmake, nevadi, stiahol som si zdrojaky :
        http://www.cmake.org/files/v2.4/cmake-2.4.6.tar.gz

        vsetko prekompiloval a nainstaloval.

        najskor skuska :
        wodim -dummy -dev=/dev/hdd -speed=4 GamesKnoppix-3.7-0.2-EN.iso

        potom naostro :
        wodim -dev=/dev/hdd -speed=4 GamesKnoppix-3.7-0.2-EN.iso

        vsetko OK

        A zle napalene CD pomocou cdrecord zostali v kvetinaci
      • Re: napalovanie pomocou cdrecord 09.02.2007 | 17:59
        Avatar Dušan Ďurech Debian Lenny 5.0  Používateľ
        No wodim vcera fungoval, ale dneska nechce, ta ista chyba ako pri cdrecord.

        cat burn.sh
        wodim -dev=/dev/hdd -speed=4 KNOPPIX_V5.1.1CD-2007-01-04-EN.iso

        ./burn.sh

        wodim: No write mode specified.
        wodim: Asuming -tao mode.
        wodim: Future versions of wodim may have different drive dependent defaults.
        Device type : Removable CD-ROM
        Version : 0
        Response Format: 2
        Capabilities :
        Vendor_info : 'HL-DT-ST'
        Identification : 'DVD-RAM GSA-H20L'
        Revision : '1.01'
        Device seems to be: Generic mmc2 DVD-R/DVD-RW.
        Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
        Driver flags : MMC-3 SWABAUDIO BURNFREE
        Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
        Speed set to 2822 KB/s
        Starting to write CD/DVD at speed 16.0 in real TAO mode for single session.
        Last chance to quit, starting real write 0 seconds. Operation starts.
        Errno: 0 (Success), write_g1 scsi sendcmd: no error
        CDB: 2A 00 00 00 F5 37 00 00 1F 00
        status: 0x2 (CHECK CONDITION)
        Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 09 00 00 00
        Sense Key: 0x4 Hardware Error, Segment 0
        Sense Code: 0x09 Qual 0x00 (track following error) Fru 0x0
        Sense flags: Blk 0 (not valid)
        resid: 63488
        cmd finished after 8.251s timeout 40s
        write track data: error after 128563200 bytes
        wodim: A write error occured.
        wodim: Please properly read the error message above.
        • Re: napalovanie pomocou cdrecord 09.02.2007 | 18:48
          WlaSaTy   Návštevník
          a ake rychlosti vie vobec pouzit ta vypalovacka? toto mi robilo ked som bud uplne nevypol rozhranie ide-scsi alebo pouzil nespravnu rychlost alebo nekompatibilne medium.