sudo smartctl -x /dev/sda smartctl 6.2 2013-07-26 r3841 [i686-linux-4.4.0-116-generic] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD3200AAJS-60Z0A0 Serial Number: WD-WMAV2HA98991 LU WWN Device Id: 5 0014ee 05804326b Firmware Version: 03.03E03 User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Apr 19 15:30:39 2018 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6180) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 75) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 136 134 021 - 4166 4 Start_Stop_Count -O--CK 094 094 000 - 6030 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 093 093 000 - 5236 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 6006 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 007 000 - 93 188 Command_Timeout -O--CK 100 057 000 - 215 190 Airflow_Temperature_Cel -O---K 065 050 040 - 35 192 Power-Off_Retract_Count -O--CK 200 200 000 - 367 193 Load_Cycle_Count -O--CK 198 198 000 - 6030 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 84 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 93 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 93 [20] occurred at disk power-on lifetime: 3662 hours (152 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 0c bc 00 45 2a 40 00 Error: UNC at LBA = 0xcbc00452a = 54693741866 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 10 00 0c bc 00 45 2e 40 08 00:15:56.283 READ FPDMA QUEUED 60 00 02 00 08 00 0c bc 00 45 2c 40 08 00:15:56.283 READ FPDMA QUEUED 60 00 02 00 00 00 0c bc 00 45 2a 40 08 00:15:56.283 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:15:56.257 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:15:56.256 IDENTIFY DEVICE Error 92 [19] occurred at disk power-on lifetime: 3662 hours (152 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 0c bc 00 45 2a 40 00 Error: UNC at LBA = 0xcbc00452a = 54693741866 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 00 00 0c bc 00 45 28 40 08 00:15:53.945 READ FPDMA QUEUED 60 00 08 00 00 00 0c bc 00 45 20 40 08 00:15:53.944 READ FPDMA QUEUED 60 00 20 00 00 00 0c bb 00 45 68 40 08 00:15:53.944 READ FPDMA QUEUED 60 00 08 00 00 00 0c bb 00 45 60 40 08 00:15:53.943 READ FPDMA QUEUED 60 00 20 00 00 00 0c ba 00 45 d0 40 08 00:15:53.943 READ FPDMA QUEUED Error 91 [18] occurred at disk power-on lifetime: 3659 hours (152 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 0c bc 00 45 2a 40 00 Error: UNC at LBA = 0xcbc00452a = 54693741866 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 48 00 c0 00 0c bc 00 45 d8 40 08 00:11:32.904 READ FPDMA QUEUED 60 00 08 00 b8 00 0c bc 00 45 d0 40 08 00:11:32.903 READ FPDMA QUEUED 60 00 08 00 b0 00 0c bc 00 45 c8 40 08 00:11:32.903 READ FPDMA QUEUED 60 00 08 00 a8 00 0c bc 00 45 c0 40 08 00:11:32.903 READ FPDMA QUEUED 60 00 08 00 a0 00 0c bc 00 45 b8 40 08 00:11:32.903 READ FPDMA QUEUED Error 90 [17] occurred at disk power-on lifetime: 3658 hours (152 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 0c bc 00 45 2a 40 00 Error: UNC at LBA = 0xcbc00452a = 54693741866 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 0c bd 00 45 18 40 08 01:00:55.211 READ FPDMA QUEUED 60 00 08 00 00 00 0c bd 00 45 10 40 08 01:00:55.211 READ FPDMA QUEUED 60 00 08 00 f0 00 0c bd 00 45 08 40 08 01:00:55.211 READ FPDMA QUEUED 60 00 08 00 e8 00 0c bd 00 45 00 40 08 01:00:55.211 READ FPDMA QUEUED 60 00 08 00 e0 00 0c bc 00 45 f8 40 08 01:00:55.211 READ FPDMA QUEUED Error 89 [16] occurred at disk power-on lifetime: 3658 hours (152 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 0c bc 00 45 2a 40 00 Error: UNC at LBA = 0xcbc00452a = 54693741866 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 b8 00 0c bc 00 45 e0 40 08 01:00:45.676 READ FPDMA QUEUED 60 00 18 00 b0 00 0c bc 00 45 c8 40 08 01:00:45.668 READ FPDMA QUEUED 60 00 08 00 a8 00 0c bc 00 45 c0 40 08 01:00:45.659 READ FPDMA QUEUED 60 00 08 00 a0 00 0c bc 00 45 b8 40 08 01:00:45.651 READ FPDMA QUEUED 60 00 08 00 98 00 0c bc 00 45 b0 40 08 01:00:45.643 READ FPDMA QUEUED Error 88 [15] occurred at disk power-on lifetime: 3658 hours (152 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 0c bc 00 45 2a 40 00 Error: UNC at LBA = 0xcbc00452a = 54693741866 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 0c bc 00 45 38 40 08 01:00:36.177 READ FPDMA QUEUED 60 00 08 00 18 00 0c bc 00 45 30 40 08 01:00:36.177 READ FPDMA QUEUED 60 00 08 00 10 00 0c bc 00 45 28 40 08 01:00:36.177 READ FPDMA QUEUED 60 00 08 00 08 00 0c bc 00 45 20 40 08 01:00:36.176 READ FPDMA QUEUED 60 00 e0 00 10 00 0c ba 00 45 e8 40 08 01:00:36.176 READ FPDMA QUEUED Error 87 [14] occurred at disk power-on lifetime: 3658 hours (152 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 0c bc 00 45 2a 40 00 Error: UNC at LBA = 0xcbc00452a = 54693741866 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 0c bc 00 45 38 40 08 00:45:42.411 READ FPDMA QUEUED 60 00 08 00 18 00 0c bc 00 45 30 40 08 00:45:42.411 READ FPDMA QUEUED 60 00 08 00 10 00 0c bc 00 45 28 40 08 00:45:42.410 READ FPDMA QUEUED 60 00 08 00 08 00 0c bc 00 45 20 40 08 00:45:42.410 READ FPDMA QUEUED 60 00 e0 00 10 00 0c ba 00 45 e8 40 08 00:45:42.409 READ FPDMA QUEUED Error 86 [13] occurred at disk power-on lifetime: 3658 hours (152 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 0c bc 00 45 2a 40 00 Error: UNC at LBA = 0xcbc00452a = 54693741866 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 0c bd 00 45 18 40 08 00:45:32.421 READ FPDMA QUEUED 60 00 08 00 f0 00 0c bd 00 45 10 40 08 00:45:32.421 READ FPDMA QUEUED 60 00 08 00 e8 00 0c bd 00 45 08 40 08 00:45:32.404 READ FPDMA QUEUED 60 00 08 00 e0 00 0c bd 00 45 00 40 08 00:45:32.404 READ FPDMA QUEUED 60 00 08 00 d8 00 0c bc 00 45 f8 40 08 00:45:32.404 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4971 - # 2 Short offline Completed without error 00% 23 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 22/35 Celsius Lifetime Min/Max Temperature: 22/50 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (24) Index Estimated Time Temperature Celsius 25 2018-04-19 13:23 26 ******* 26 2018-04-19 13:24 27 ******** 27 2018-04-19 13:25 28 ********* 28 2018-04-19 13:26 28 ********* 29 2018-04-19 13:27 29 ********** 30 2018-04-19 13:28 29 ********** 31 2018-04-19 13:29 29 ********** 32 2018-04-19 13:30 30 *********** ... ..( 2 skipped). .. *********** 35 2018-04-19 13:33 30 *********** 36 2018-04-19 13:34 31 ************ 37 2018-04-19 13:35 31 ************ 38 2018-04-19 13:36 32 ************* ... ..( 2 skipped). .. ************* 41 2018-04-19 13:39 32 ************* 42 2018-04-19 13:40 33 ************** ... ..( 8 skipped). .. ************** 51 2018-04-19 13:49 33 ************** 52 2018-04-19 13:50 34 *************** ... ..( 4 skipped). .. *************** 57 2018-04-19 13:55 34 *************** 58 2018-04-19 13:56 ? - 59 2018-04-19 13:57 22 *** 60 2018-04-19 13:58 23 **** 61 2018-04-19 13:59 24 ***** 62 2018-04-19 14:00 25 ****** 63 2018-04-19 14:01 25 ****** 64 2018-04-19 14:02 26 ******* 65 2018-04-19 14:03 27 ******** 66 2018-04-19 14:04 27 ******** 67 2018-04-19 14:05 28 ********* 68 2018-04-19 14:06 29 ********** 69 2018-04-19 14:07 29 ********** 70 2018-04-19 14:08 29 ********** 71 2018-04-19 14:09 30 *********** ... ..( 2 skipped). .. *********** 74 2018-04-19 14:12 30 *********** 75 2018-04-19 14:13 31 ************ 76 2018-04-19 14:14 31 ************ 77 2018-04-19 14:15 32 ************* 78 2018-04-19 14:16 32 ************* 79 2018-04-19 14:17 32 ************* 80 2018-04-19 14:18 33 ************** ... ..( 9 skipped). .. ************** 90 2018-04-19 14:28 33 ************** 91 2018-04-19 14:29 34 *************** ... ..( 3 skipped). .. *************** 95 2018-04-19 14:33 34 *************** 96 2018-04-19 14:34 ? - 97 2018-04-19 14:35 22 *** 98 2018-04-19 14:36 22 *** 99 2018-04-19 14:37 24 ***** 100 2018-04-19 14:38 25 ****** 101 2018-04-19 14:39 26 ******* 102 2018-04-19 14:40 26 ******* 103 2018-04-19 14:41 27 ******** 104 2018-04-19 14:42 27 ******** 105 2018-04-19 14:43 28 ********* 106 2018-04-19 14:44 29 ********** 107 2018-04-19 14:45 29 ********** 108 2018-04-19 14:46 30 *********** 109 2018-04-19 14:47 30 *********** 110 2018-04-19 14:48 30 *********** 111 2018-04-19 14:49 31 ************ ... ..( 3 skipped). .. ************ 115 2018-04-19 14:53 31 ************ 116 2018-04-19 14:54 32 ************* 117 2018-04-19 14:55 32 ************* 118 2018-04-19 14:56 33 ************** ... ..( 8 skipped). .. ************** 127 2018-04-19 15:05 33 ************** 0 2018-04-19 15:06 34 *************** ... ..( 15 skipped). .. *************** 16 2018-04-19 15:22 34 *************** 17 2018-04-19 15:23 35 **************** ... ..( 6 skipped). .. **************** 24 2018-04-19 15:30 35 **************** SCT Error Recovery Control: Read: 85 (8,5 seconds) Write: 85 (8,5 seconds) Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x8000 4 3328 Vendor specific lacko@lacko-System-Product-Name ~ $ ^C lacko@lacko-System-Product-Name ~ $