jadro som si nakonfiguroval ale nemozem zaviest ovladace a neviem preco pridavam vypisy
lspci -v
05:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) (prog-if 10 [OHCI])
Subsystem: Fujitsu Siemens Computers Unknown device 10b8
Flags: bus master, medium devsel, latency 64, IRQ 20
Memory at c0203000 (32-bit, non-prefetchable) [size=4K]
Memory at c0202000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [60] Power Management version 2
Kernel driver in use: firewire_ohci
.config
cat .config | grep 1394
# IEEE 1394 (FireWire) support
CONFIG_IEEE1394=y
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=y
CONFIG_IEEE1394_VIDEO1394=y
CONFIG_IEEE1394_SBP2=y
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
CONFIG_IEEE1394_ETH1394_ROM_ENTRY=y
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=y
CONFIG_IEEE1394_RAWIO=y
# CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set
CONFIG_FIREWIRE_OHCI=y
CONFIG_FIREWIRE_OHCI_DEBUG=y
CONFIG_IEEE1394_OHCI1394=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_HCD_SSB is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set
# CONFIG_FIREWIRE_OHCI_REMOTE_DMA is not set
lsmod
snd_hda_intel 401428 0
snd_pcm 72840 1 snd_hda_intel
bcm43xx 424096 0
snd_timer 22288 1 snd_pcm
snd 47496 3 snd_hda_intel,snd_pcm,snd_timer
snd_page_alloc 10064 2 snd_hda_intel,snd_pcm
modprobe
modprobe ohci1394
FATAL: Module ohci1394 not found.
modprobe ieee1394
FATAL: Module ieee1394 not found.
neviete kde som spravil chybu???
ked nemozem zaviest moduly na pracu zo zariadenim ???
mam jadro
2.6.26-rc4
dakujem
CONFIG_IEEE1394*=yno, pokial si z takto nastaveneho jadra aj nastartoval, tak si pozri rozdiel medzi zahrnutim ovladaca do jadra, ako modul a nezahrnutim.
a pozri si vystup z
dmesg.a ak sa nemylim tak som ich dal aby boli automaticky v jadre a nie ako modul
dmesg | grep 1394video1394: Installed video1394 module
ieee1394: raw1394: /dev/raw1394 device initialized
NOTE: The dv1394 driver is unsupported and may be removed in a future Linux release. Use raw1394 instead.
Ja sa márne pokúšam rozchodiť MiniDV kameru na Ubuntu HH.
Už som skúsil snáď všetko čo sa dalo a čo som na nete našiel. Možno ten tvoj postup pomôže.
Vopred ďakujem.