konfiguracia slackware10.2
caw, nainstaloval som slackware10.2. pocas instalacie som nastavoval internet (ip.mask,gate...) a po prihlaseni mi net neisiel. spustal som netconfig este raz a nic, pozrel som do /etc/rc.d/rc.inet1.conf a vsetko tam bolo v poriadku neviem si dat rady..
pocas instalacie som instaloval aj lilo ale vyhodilo error ze nic s toho. musel som pouzit bootdisk. zaujimave bolo ze pred instalaciou slackwaru som sformatoval sdisk a spravil particie s cfdisk a po instalacii, ked som nepouzil bootdisk tak nabehol grub ktory som tam mal s fedorou pred formatovanim disku.
viete pomoct aspon s tym netom?
Everything is proceeding as I have foreseen.
Pre pridávanie komentárov sa musíte prihlásiť.
modprobe ne io=0x360, prepnem sa do druhej konzoly a vyskusam tak to nevie najst. ked vyskusammodprobe 8390tak sa nestazuje, ale ked dam vyhladavat len ten modul tak ho tiez nenajde# lspci- nasiel som vo vypise:06:08.0 Ethrnet controller: Intel corporation 82562ET/EZ/GT/GZ/ - pro/100 VE (LOM) Ethernet controller (rev 01)# ifconfig eth0 [moja IP] netmask 255.255.255.0 up SIOCFADDR: No such device eth0: unknown interface: No such device SIOCSIFNETMASK: No such device eth0: unknown interface: No such deviceroot@localhost:~# modprobe -v eepro100 /sbin/insmod /lib/modules/2.4.31/kernel/drivers/net/mii.o.gz Using /lib/modules/2.4.31/kernel/drivers/net/mii.o.gz Symbol version prefix '' /sbin/insmod /lib/modules/2.4.31/kernel/drivers/net/eepro100.o.gz Using /lib/modules/2.4.31/kernel/drivers/net/eepro100.o.gz /lib/modules/2.4.31/kernel/drivers/net/eepro100.o.gz: init_module: No such device /lib/modules/2.4.31/kernel/drivers/net/eepro100.o.gz: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.31/kernel/drivers/net/eepro100.o.gz: insmod /lib/modules/2.4.31/kernel/drivers/net/eepro100.o.gz failed # delete mii /lib/modules/2.4.31/kernel/drivers/net/eepro100.o.gz: insmod eepro100 failed root@localhost:~# dmesg | tail shpchp: shpc_init : shpc_cap_offset == 0 shpchp: shpc_init : shpc_cap_offset == 0 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 shpchp: shpc_init : shpc_cap_offset == 0 shpchp: shpc_init : shpc_cap_offset == 0 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 keyboard: Timeout - AT keyboard not present?(f3) keyboard: Timeout - AT keyboard not present?(f4) eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin and others# ifconfig eth0 Link encap:Ethernet HWaddr 00:13:20:14:80:FA inet addr:[moja ip] Bcast:192.168.19.255 Mask:255.255.255.0 inet6 addr: 2002:c0a8:1349:4:213:20ff:fe14:80fa/64 Scope:Global inet6 addr: fec0::4:213:20ff:fe14:80fa/64 Scope:Site inet6 addr: fe80::213:20ff:fe14:80fa/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:453 errors:0 dropped:0 overruns:0 frame:0 TX packets:255 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:298169 (291.1 KiB) TX bytes:33716 (32.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.255.255.255 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1173 errors:0 dropped:0 overruns:0 frame:0 TX packets:1173 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:105258 (102.7 KiB) TX bytes:105258 (102.7 KiB) # route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface [ mojaip ] * 255.255.255.0 U 0 0 0 eth0 default [ moja ip ] 0.0.0.0 UG 0 0 0 eth0# ifconfig lo Link encap:Local Loopback inet add: 127.0.0.1 Mask: 255.0.0.0 UP LOOPBACK RUNNING MTU: 16436 Metric: 1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carried:0 collisions:0 txueuelen:0 RX bytes:0 (0,0 b) TX bytes:0 (0,0 b) # route Kernel IP routing table Destination Gateway Genmask Flugs Metric Ref Use iface loopback * 255.0.0.0 U 0 0 0 loasi to nebude dobre sformatovane :( a LILO sa mi vobec nenainstalovalo/sbin/modprobe ne2k_pciak ti network supplemental disk oznami, ze nasiel sietovku s driverom ne2k_pci.# LILO configuration file # generated by 'liloconfig' # # Start LILO global section lba32 # Allow booting past 1024th cylinder with a recent BIOS boot = /dev/hda2 message = /boot/boot_message.txt prompt timeout = 1200 # Override dangerous defaults that rewrite the partition table: change-rules reset # Normal VGA console vga = normal # Windows bootable partition config begins other = /dev/hda3 label = Windows table = /dev/hda # Windows bootable partition config ends # Linux bootable partition config begins image = /boot/vmlinuz root = /dev/hda2 label = Linux read-only # Linux bootable partition config endsmozete mi prosim napisat ako to lilo preinstalovat?# Windows bootable partition config begins other = /dev/sda1 label = Windows table = /dev/sda # Windows bootable partition config endsale ked som v biose prepol aby bootoval z disku kde mam len slackware + lilo ako zavadzac tak sa znovu spusil grub (ktory som tam mal pred formatovanim disku a instalaciou slacku) ale uz nemal co bootovat tak som musel restartovat. lilo sa vobec nechytil