Takze prave mam openSUSE 11.2, no mam taky isty problem ako v kubuntu 9.10 ze sa nemozem pripojit na svoju domacu siet, prosim surne o pomoc je to skryta siet je to wep 40 alebo 60, no ked si vsetko aj manualne nastavim tak ani za svet sa mi nechce pripojit
v gnome vsetko v poho ale ja chcem kde a nejako sa isto da ta wifi pripojit len neviem ako bohaca
Wifi openSUSE 11.2 KDE
Pre pridávanie komentárov sa musíte prihlásiť.
sunapis rootove heslo
iwconfigeth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"JBwireless"
Mode:Managed Frequency:2.427 GHz Access Point: 00:60:B3:F3:30:37
Bit Rate=12 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=25/70 Signal level=-85 dBm Noise level=-104 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Chyba je v tom, ze ked sa clovek snazi napoprve pripojit (prvy krat od instalacie), tak to nepojde a ked sa potom clovek s tym hra a meni tie nastavenia (po tom, co prvykrat uz nastavil patricne udaje a je to ulozene medzi wireless spojeniami), tak sa to nechce rozbehnut.
Ak toto nezabere, tak este jedno riesenie mam v zalohe. No vyskusaj toto najprv
Bez toho ťažko pomôcť
skús príkazy lsusb, alebo lspci --ako root
malo by ti to vypísať
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
00:00.0 Host bridge: ATI Technologies Inc Device 5a31 (rev 01)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:05.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:06.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:07.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA
00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0)
00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1)
00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2)
00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3)
00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4)
00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI)
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 13)
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon Xpress 200M]
02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
08:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3)
08:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 17)
08:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 08)
08:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
spusti YAST: - sieťové karty
vypni knetworkmanager a použi tradičný spôsob
tam nakonfiguruj wifi kartu
a nakonfigurujem tak isto tak nejde... uz som aj aktualizoval na najnovsie kde neviem v com moze byt chyba?
až dokončím toto svoje trápenie s Fedorou12
a budem sa Ti venovať
sorry
Mimochodom máš radar?
skus v konzole:
iwlist scan
mimochodom ci je siet skryta alebo nie - to je ina otazka
a este nieco - v kde - hned je v tom menu aj ten wifi radar