konflikty IRQ >> EHCI_HCD a OHCI_HCD
Zdravim. Na notebook Asus A6R-B002 som sa rozhodol nainstalovat Gentoo Linux. Vsetko islo v pohode, mam nahodene KDE a potrebny softver. Problem nastal az potom co som sa rozhodol k notebooku pripojit usb zariadenie (mys, usb disk..).
Vypis dmesg:
usb 2-1: new low speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:13.0: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
Vypis /proc/interrupts:
201: 100000 IO-APIC-level ehci_hcd:usb1, ohci_hcd:usb2, ohci_hcd:usb3
Vypis lspci -v:
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog
-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1187
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 201
Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable
-
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog
-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 1187
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 201
Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable
Skusal som uz rozne kernely gentoo-sources(2.6.15-r1 az r7), ck-sources(2.6.15_p5), mm-sources(2.6.16_rc5-r10),nitro-sources(2.6.15-r3), rozne boot parametre pre kernel (irqpoll ,pci=routeirq, pci=biosirq,...etc), ale bezvysledne.Vopred vam dakujem za snahu pomoct mi, budem rad ked mi aspon jeden z prispevkov pomoze vyriesit tento na prvy pohlad banalny problem.
Pre pridávanie komentárov sa musíte prihlásiť.
-
-
doplnok 10.03.2006 | 00:34
chembro Používateľ
este som zabudol pridat cast z vypisu lspci -v: 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (pro g-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. Unknown device 1187 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 201 Memory at febfd000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Re: doplnok 15.03.2006 | 12:51petulik Návštevníkmam presne ten isty notebook. neinstaloval som gentoo, ale podobny problem som mal napriklad so suse. tam mi pomohol parameter jadra IRQPOLL
-
Re: Re: doplnok 31.03.2006 | 22:09prosim ta. poslal by si mi svoj kernel config ? Nejak ma serka sietovka a neviem na to prijst. NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0c 0005 c07f media 50. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008a047. (queue head) eth0: Tx descriptor 1 is 0008a095. eth0: Tx descriptor 2 is 0008a047. eth0: Tx descriptor 3 is 0008a03c. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
-
Re: Re: Re: doplnok 31.03.2006 | 23:28petulik Návštevníkhehe :), ja uz nemam gentoo, momentalne som na kubuntu, tam ten program nemam.
-
-
-
-
Re: konflikty IRQ >> EHCI_HCD a OHCI_HCD 01.04.2006 | 11:23WlaSaTy Návštevníktak ma napadlo, nevypol si apic popripade lapic (a podobne) pri starte jadra?
-
Re: Re: konflikty IRQ >> EHCI_HCD a OHCI_HCD 01.04.2006 | 18:00nie, vsetko je zapnute :-)
-
-
