Dobry den,
mam Free Mandriva Linux 2007
jadro : 2.6.20
cdrecord -version
Cdrecord-ProDVD-Clone 2.01.01a11 (i686-pc-linux-gnu) Copyright (C) 1995-2006 J�g Schilling
cdrecord -scanbus -dev=ATA
Cdrecord-ProDVD-Clone 2.01.01a11 (i686-pc-linux-gnu) Copyright (C) 1995-2006 J�g Schilling
scsidev: 'ATA'
devname: 'ATA'
scsibus: -2 target: -2 lun: -2
Warning: Using badly designed ATAPI via /dev/hd* interface.
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.8'.
scsibus1:
1,0,0 100) *
1,1,0 101) 'HL-DT-ST' 'DVD-RAM GSA-H20L' '1.01' Removable CD-ROM
Vcera som napaloval ISO obraz pomocou prikazu:
cdrecord dev=/dev/hdd KNOPPIX_V5.1.1CD-2007-01-04-EN.iso
prebehlo OK
Dneska som chcel napalit, dalsie pomocou :
cdrecord speed=8 dev=/dev/hdd GamesKnoppix-3.7-0.2-EN.iso
ale napise mi to :
Sence Key: 0x4 hardware Error, Segment 0
cmd finished after 8.684s timeout 40s
write track data: error after 1015808 bytes
cdrecord: A write error occured
cdrecord: please properly read the error message above.
cdrecord: Success. close track/session: scsi sendcmd: no error
potom som napalovanie simuloval pomocou "dummy" a ziadne chyby nenastali.
Za odpovede vopred dakujem.
napalovanie pomocou cdrecord
Pre pridávanie komentárov sa musíte prihlásiť.
dvd+rw-tools
wodim
Stiahol som si zdrojaky :
http://ftp.debian.org/debian/pool/main/c/cdrkit/cdrkit_1.1.2.orig.tar.gz
hmm, nemam cmake, nevadi, stiahol som si zdrojaky :
http://www.cmake.org/files/v2.4/cmake-2.4.6.tar.gz
vsetko prekompiloval a nainstaloval.
najskor skuska :
wodim -dummy -dev=/dev/hdd -speed=4 GamesKnoppix-3.7-0.2-EN.iso
potom naostro :
wodim -dev=/dev/hdd -speed=4 GamesKnoppix-3.7-0.2-EN.iso
vsetko OK
A zle napalene CD pomocou cdrecord zostali v kvetinaci
cat burn.sh
wodim -dev=/dev/hdd -speed=4 KNOPPIX_V5.1.1CD-2007-01-04-EN.iso
./burn.sh
wodim: No write mode specified.
wodim: Asuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identification : 'DVD-RAM GSA-H20L'
Revision : '1.01'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Speed set to 2822 KB/s
Starting to write CD/DVD at speed 16.0 in real TAO mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
Errno: 0 (Success), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 00 F5 37 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 09 00 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x09 Qual 0x00 (track following error) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 63488
cmd finished after 8.251s timeout 40s
write track data: error after 128563200 bytes
wodim: A write error occured.
wodim: Please properly read the error message above.