XMMS - pocuvanie radia

Zadal som teda v konzole toto: pnpdump --reset Tu je vypis: # $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $ # Release isapnptools-1.26 # # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of the output file format, see isapnp.conf(5) # # For latest information and FAQ on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE # # Trying port address 0273 # Board 1 has serial identifier d7 ff ff ff ff 03 00 73 16 # (DEBUG) (READPORT 0x0273) (ISOLATE CLEAR) (IDENTIFY *) (VERBOSITY 2) (CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING # Card 1: (serial identifier d7 ff ff ff ff 03 00 73 16) # Vendor Id ESS0003, No Serial Number (-1), checksum 0xD7. # Version 1.0, Vendor version 1.0 # ANSI string -->ESS ES1869 Plug and Play AudioDrive<-- # # Logical device id ESS0006 # Device supports vendor reserved register @ 0x3c # Device supports vendor reserved register @ 0x3d # Device supports vendor reserved register @ 0x3e # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE ESS0003/-1 (LD 0 # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0800 # Maximum IO base address 0x0ff8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x0800)) (NAME "ESS0003/-1[0]{ESS ES1869 Plug and Play AudioDrive}") # (ACT Y) )) # # Logical device id ESS1869 # Device supports vendor reserved register @ 0x3c # Device supports vendor reserved register @ 0x3d # Device supports vendor reserved register @ 0x3e # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE ESS0003/-1 (LD 1 # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # First DMA channel 1. # 8 bit DMA only # Logical device is a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 1)) # Next DMA channel 0 or 3. # 8 bit DMA only # Logical device is a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # IRQ 5. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0220 # IO base alignment 1 bytes # *** Bad resource data: Base alignment 0 - changed to 1 # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 1 bytes # *** Bad resource data: Base alignment 0 - changed to 1 # Number of IO addresses required: 4 # (IO 1 (SIZE 4) (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0330 # Maximum IO base address 0x0330 # IO base alignment 1 bytes # *** Bad resource data: Base alignment 0 - changed to 1 # Number of IO addresses required: 2 # (IO 2 (SIZE 2) (BASE 0x0330)) # Start dependent functions: priority acceptable # First DMA channel 1. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 1)) # Next DMA channel 0 or 3. # 8 bit DMA only # Logical device is a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # IRQ 5, 7, 9, 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 1 bytes # *** Bad resource data: Base alignment 0 - changed to 1 # Number of IO addresses required: 4 # (IO 1 (SIZE 4) (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 48 bytes # Number of IO addresses required: 2 # (IO 2 (SIZE 2) (BASE 0x0300)) # Start dependent functions: priority acceptable # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # IRQ 5, 7, 9, 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 1 bytes # *** Bad resource data: Base alignment 0 - changed to 1 # Number of IO addresses required: 4 # (IO 1 (SIZE 4) (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 48 bytes # Number of IO addresses required: 2 # (IO 2 (SIZE 2) (BASE 0x0300)) # Start dependent functions: priority acceptable # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # IRQ 5, 7, 9, 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 1 bytes # *** Bad resource data: Base alignment 0 - changed to 1 # Number of IO addresses required: 4 # (IO 1 (SIZE 4) (BASE 0x0388)) # Start dependent functions: priority functional # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # IRQ 5, 7, 9, 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # End dependent functions (NAME "ESS0003/-1[1]{ESS ES1869 Plug and Play AudioDrive}") # (ACT Y) )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY)