wlan0: no IPv6 routers present CE: hpet increasing min_delta_ns to 15000 nsec tg3 0000:07:00.0: irq 31 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth0: link is not ready wlan0: no IPv6 routers present tg3 0000:07:00.0: irq 31 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth0: link is not ready tg3 0000:07:00.0: irq 31 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth0: link is not ready wlan0: no IPv6 routers present tg3 0000:07:00.0: irq 31 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth0: link is not ready tg3 0000:07:00.0: irq 31 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth0: link is not ready wlan0: no IPv6 routers present tg3 0000:07:00.0: irq 31 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth0: link is not ready tg3 0000:07:00.0: irq 31 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth0: link is not ready wlan0: no IPv6 routers present tg3 0000:07:00.0: irq 31 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth0: link is not ready tg3 0000:07:00.0: irq 31 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth0: link is not ready wlan0: no IPv6 routers present
na eth0 mi internet z toho isteho routru ide. Wifi pripojenie na sestrinom notebooku ide tiez.
Pouzivam wicd a wicd-client
Co s tym moze byt? Vdaka
dmesg konci tym istym co pred tym, wicd-client mi pri snahe znovu pripojit sa na wifi nevie pridelit IP adresu, eth0 funguje.
wlan0: no IPv6 routers present/ako to je s IPV6 u vas doma?//do najblizsieho restartu sa da odstranit pomocou
modprobe -r ipv6, tak skusaj/Kto si to nechce citat, jednoducho nech si do
/etc/modprobe.d/modprobe.confprida:alias net-pf-10 off
konecnou skuskou je prazdny vysledok vypisu
lsmod | grep ipv6Uvidim ci tato rada pomohla.
Ja osobne som si myslel, ze bude stacit jednoducho zakazat load ipv6 na zaciatku bootu ( editovat /etc/rc.conf a do MODULES pridat !ipv6 ). Ale to nestacilo.. Trebalo pouzit tu wiki.
V priebehu dalsich dni budem hlasit vysledky, zatial vdaka.
Wicd-client mi hlasi pri pripajani sa na moju domacu essid "Connection Failed: Unable to Get IP Address"
Na niektorych forach som nasiel, ze mam vyskusat vymenit dhcpcd za dhclient priamo v nastaveni wicd-clientu, nastavil som no i tak to spadlo.
Koniec dmesg-u:
fb0: inteldrmfb frame buffer deviceregistered panic notifier
acpi device:07: registered as cooling_device2
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input13
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
Adding 1028120k swap on /dev/sda6. Priority:-1 extents:1 across:1028120k
tg3 0000:07:00.0: irq 31 for MSI/MSI-X
tg3 0000:07:00.0: irq 31 for MSI/MSI-X
tg3 0000:07:00.0: irq 31 for MSI/MSI-X
tg3 0000:07:00.0: irq 31 for MSI/MSI-X
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
tg3: eth0: Link is down.
tg3 0000:07:00.0: irq 31 for MSI/MSI-X
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
tg3 0000:07:00.0: irq 31 for MSI/MSI-X
tg3 0000:07:00.0: irq 31 for MSI/MSI-X
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
Co s tym moze byt?
Vdaka