Dobry den. Pohybujem sa v linuxe uz nejaku tu dobu a vzdy ked som nieco cez USB pripojil, nabehla mi ikonka ze mam pripojene a mohol som citat :D. No neviem napriklad ako pripojit fotak, pretoze po spojeni s pc mi nenabehne nic aj ked je spojeny... Na internete som nasiel iba fora s riesenim problemov ako moutnut iso alebo inu partisnu. Potreboval by som to tak polopatisticky vysvetlit lebo s tymto som sa este nestretol. "Click-Click forever" 8-)
Dakujem za odpovede
Pripojenie fotoaparatu
There is no flag large enough to cover the shame of killing innocent people
Pre pridávanie komentárov sa musíte prihlásiť.
pride dlhy vystup z ktoreho ta zaujimaju tieto riadky niekde na konci :
SCSI device sdb: 253952 512-byte hdwr sectors (130 MB)
sdb: Write Protect is off
sdb: Mode Sense: 43 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 253952 512-byte hdwr sectors (130 MB)
sdb: Write Protect is off
sdb: Mode Sense: 43 00 00 00
sdb: assuming drive cache: write through
sdb: sdb1
sd 4:0:0:0: Attached scsi removable disk sdb
sd 4:0:0:0: Attached scsi generic sg1 type 0
Device driver target4:0:1 lacks bus and class support for being resumed.
hlavne ten sdb:sdb1 (moze byt aj ine napr sda:sda1 a pod)
- znamena to ze usb zariadenie najdes pod /dev/sdb1
takze si vytvoris adresar #mkdir /mnt/fotak
a namountujes fotak #mount /dev/sdb1 /mnt/fotak
potom #cd /mnt/fotak
a je to
alebo je este jedna moznost, prepni ten fotak do modu prenosneho disku (ako je to mozne aj u mojeho). alebo jednoducho stahuj fotky cez citacku, ajtak je to rychlejsie.
Ja som v tomto novy...
Dakujem
skus sem dat vypis z lsusb a lsmod, mozno ti len chyba nacitany modul pre scsi disk ...
Ten vypis je tu:
sudo modprobe scsi_mod. To by mal byť ten modul pre scsi. Poprípade takto skús zaviesť aj: usb_storagevypisem len ten koniec, je to prilis dlhe, alebo ak chete mozem cele neikde nahodit
[17179596.444000] EXT3 FS on hda6, internal journal
[17179596.556000] NET: Registered protocol family 17
[17179597.416000] kjournald starting. Commit interval 5 seconds
[17179597.424000] EXT3 FS on hda8, internal journal
[17179597.424000] EXT3-fs: mounted filesystem with ordered data mode.
[17179600.536000] NET: Registered protocol family 10
[17179600.536000] lo: Disabled Privacy Extensions
[17179600.536000] IPv6 over IPv4 tunneling driver
[17179604.804000] ACPI: Power Button (FF) [PWRF]
[17179604.804000] ACPI: Power Button (CM) [PWRB]
[17179604.968000] ibm_acpi: ec object not found
[17179605.008000] pcc_acpi: loading...
[17179609.052000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[17179609.052000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[17179609.052000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[17179610.876000] eth0: no IPv6 routers present
[17179613.920000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[17179613.920000] apm: overridden by ACPI.
[17179636.548000] Bluetooth: Core ver 2.8
[17179636.548000] NET: Registered protocol family 31
[17179636.548000] Bluetooth: HCI device and connection manager initialized
[17179636.548000] Bluetooth: HCI socket layer initialized
[17179636.816000] Bluetooth: L2CAP ver 2.8
[17179636.816000] Bluetooth: L2CAP socket layer initialized
[17179637.576000] Bluetooth: RFCOMM socket layer initialized
[17179637.576000] Bluetooth: RFCOMM TTY layer initialized
[17179637.576000] Bluetooth: RFCOMM ver 1.7
[17179943.488000] usb 2-1: new full speed USB device using uhci_hcd and address 3
[17179943.696000] usb 2-1: configuration #1 chosen from 1 choice
[17183347.320000] SCSI subsystem initialized
[17183350.440000] usb 2-1: USB disconnect, address 3
[17183354.208000] usb 2-1: new full speed USB device using uhci_hcd and address 4
[17183354.424000] usb 2-1: configuration #1 chosen from 1 choice
[17183410.568000] usbcore: registered new driver libusual
[17183410.576000] Initializing USB Mass Storage driver...
[17183410.576000] usbcore: registered new driver usb-storage
[17183410.576000] USB Mass Storage support registered.
[17183415.708000] usb 2-1: USB disconnect, address 4
[17183419.728000] usb 2-1: new full speed USB device using uhci_hcd and address 5
[17183419.928000] usb 2-1: configuration #1 chosen from 1 choice
sudo modprobe -v sd_mod
pockat par sekund a pozriet co pribudlo do dmesg.
ak balicek tvojej distribucie
:ako ho spustim
sudo modprobe -v sg
a pozri sa do dmesg a /dev ci to nepomohlo.
gphoto2 -P